blog header

blog header

Wednesday 16 October 2019

All along the hedgerow...

 

One of the things that bothers me about modular scenery is how visible the joins can be, especially with straight edges. I've attempted to put extra flock along the sides of mine to blur the seams but with only limited success. I decided what I really needed was some hedgerows and ditches to bridge the joins and soften the straight lines. 
 

 
The base for these modules is 15mm thick MDF which sits between the two modules, ensuring that the hedgerows are fixed in place and giving me a deep area to carve ditches and plug trees into. To break up the resulting grid look I made the hedge modules different widths so that the base boards would become offset from one another.


Here's a photodump of the 11 modules I ended up building. Scroll on down for some close-ups and look at the materials used.










Here's a selection of the ground cover used on the modules. I've tried to mix up the textures a bit to give a wild look and indicate a wealth of different plants growing over the terrain. Because I was keen to crack on I haven't done a step-by-step photo guide but the basic process is as follows:

After shaping the base board and cutting any ditches with a router and dremel I applied a generous dose of readymix filler to each module. Plaster cast rocks from rock moulds, cat litter and resin casts of polystyrene stones I carved were set into this and more filler applied to blend them together.



The whole module was sprayed black, misted with a green spray then drybrushed with various greys and browns. Pigmented epoxy resin (I use Easy Compsites GlassCast) was poured into the ditches, then Woodland Scenics grasses were pushed into the wet resin to give clumps of reeds. A small amount of leaf litter was scattered onto the surface to suggest fallen leaves floating in the muddy water.



A base layer mix of black tea, green tea and coffee grounds was applied over the whole module, then a blend of Model Tree Shop foam scatters (C11, C5 and C6) were sprinkled on top. When dry the whole thing was given a liberal dose of diluted PVA. the sponge scatter soaks it up and dries solid whilst retaining its grassy look. I also sprinkled Model tree Shop static grass on whilst the dilute PVA was drying to give an additional texture and to provide shading around the hedgerows. The path areas and patches under trees were left bare of sponge scatter but had leaf litter (green tea mostly) and fine sand sprinkled on. A sparse sprinkling of pink and red flock (leftover from some cheap Chinese model trees...) gives an indication of flowers.


 The dry stone walls are resin casts of walls I built from fuller's earth cat litter.

The hurdle fencing was created from aluminium wire, brushed with readymix filler for texture.


The big trees are twisted wire, covered with a thick mix of powder filler, paint and PVA. The trunks were then drybrushed with greens and greys. The foliage is lichen glued in place with PVA, painted over with diluted PVA and sprinkled with first Model Tree Shop C11 medium sponge scatter (to give shadow) then more lightly with Model Tree Shop C15 fine sponge scatter highlights.



The hedgerows are a mix of lichen, Model Scenery Supplies lump foliage (similar to Woodland Scenics olive underbrush but more solid), Javis tree foliage (which has an excellent two-tone look giving shades and highlights all together) and cheap Chinese trees. With the trees I sprayed them with a dull green before attaching them (they were too garish before) and gave them the same highlight treatment as the big trees with PVA and Model Tree Shop C15 sponge scatter.


 
 
Hope that's helpful to somebody. I'll try and take (any!) more step-by-step photos next time and will get some pics of a full set up soon.

Lord of the Rings anybody?


Share/Bookmark

6 comments:

  1. Absolutely marvelous.... Hmm my new mossy orcs would look good on that terrain :)

    ReplyDelete
  2. They would, when are they coming to play? :)

    ReplyDelete
    Replies
    1. Say the word. Just got to finish the howdahs on the giant rhinoceros beetles :)

      Delete
  3. Very atmospheric Fimm. Well done!

    ReplyDelete
  4. Very nice. They sound robust and look beautiful.

    ReplyDelete

Fimm McCool's

Fimm McCool's